Inombolo: 20220909
Umhla: sep 9, 2022
UMTHENGI:
UMTHENGISI:Qingdao cuishi plastic machine co., Ltd
Idilesi : Yahuicun village , xianggang road , shenhai highway entrance , jiaozhou city , shandong province , china , ikhowudi yeposi : 266300
Umntu woqhagamshelwano : sevenstars lucy Mob : 0086 15753291269
www.cuishimachine.com www.cuishiextruder.com
INGCACISO YEEMPAHLA:
| Igama leMpahla
| Ubungakanani
|
| I-SJ65/33 extruder ene-auto loader kunye nesomisi(55KW motor, ABB / Delta inverter, siemens contactor, ORMON / DELTA iimitha zokulawula ubushushu kunye nemveliso 200kg / h | Iseti e-1 |
| SJ25 umbala umgca extruder yokumakisha umgca | Iseti e-1 |
| I-16-110mm umbhobho wokungunda /intloko yokufa kunye nephini lokufa kunye ne-fae bushing | Iseti e-1 |
| Umtshintshi/isihluzi sesikrini seHydraulic | Iseti e-1 |
| I-6m yetanki yokufunxa kunye ne-304 engenasici | Iseti e-1 |
| 6m itanki yamanzi okupholisa | Iseti e-1 |
| Ukukhupha iyunithi | Iseti e-1 |
| Umatshini wokusika | Iseti e-1 |
| Umatshini wokuvala indawo ephindwe kabini (ukusuka kwi-16- 50MM) | Iseti e-1 |
| Indawo enye yomatshini wokuwisa (Ukusuka kwi-63-110 mm) | Iseti e-1 |
| Amalungu asetyenzisiweyo asimahla Intlawulo yomatshini wombhobho wovavanyo | |
| I-20HP yokupholisa umoyaumoya ukupholisa uhlobo chiller amanzi kunye compressor Panasonic | Iseti e-1 |
| Uhlobo lwe-Screw compressor air 15kw | Iseti e-1 |
| I-Crusher 20-110mm swp400 enemoto 18.5kw | Iseti e-1 |
| Umshicileli weLaser | Iseti e-1 |
| FOB QINGDAO USD |
1.INTLAWULO:I-30% yentlawulo ephantsi nge-T / T, enye i-70% nge-T / T okanye i-LC ngaphambi kokuthunyelwa
2.IXESHA LOKUNIKEZWA: 30iintsuku zokusebenza
3. Iwaranti: unyaka omnyeiwaranti, inkonzo ubomi obude
HDPE 110mm umgca wokuvelisa umbhobho we-extrusion
Inkcazo ngokubanzi:
1, Ubungakanani bemveliso: PE Umbhobho OD16-OD110mm ,Umbhobho eludongeni ubukhulu ngokwemfuno umthengi
2, Umthamo wemveliso oPhezulu: 180kg/h
3、Inlet Ukupholisa ubushushu bamanzi: <25℃ Uxinzelelo lomoya:> 0.6Mpa
4, Umbane wombane: 3Phase/380V/50HZ
5.ilungele i-PE entsha kunye nemathiriyeli yokurisayikilisha.
6.design L kumatshini wombhobho.ubude phakathi kwe-21meters
16―110 umgca wokuvelisa umbhobho we-PE
A. Oomatshini abayimfuneko be-16-110mm PE Pipe Extrusion Line
- Iseti e-1 yesilayishi se-vacuum esizenzekelayo
- 1 iseti ye-hopper dryer
- Iseti ye-1 ye-Single-Screw Extruder - SJ65/33
- Iseti ye-1 ye-SJ25/25 co-extruder
- Iseti e-1 yokutshintsha isikrini esizenzekelayo
- I-1 isethi epheleleyo Iimbumba ze-16-110mm
- Iseti e-1 yeTanki yokuHlola kunye neTanki yamanzi okupholisa
- Iseti e-1 yeetrektara ezimbini zeephedrali
- Iseti e-1 ye-Cutter enothuli yasimahla
B.Iinkcukacha zeeParameters zobuGcisa zomatshini ngamnye ongentla
Ukuhamba kwenkqubo yomgca wokuvelisa umbhobho we-PE ngolu hlobo lulandelayo:
Isiphakeli seMathiriyeli → Isomisi seHopper→ Ukwandisa & ukuBumba→ uLungiso lweVacuum kunye nokuPholisa → Isishicileli→ Ukukhupha → Ukusika →umbhobho wePE wokugqibela
1.Umlayishi wezinto ezizenzekelayo
| NO | Inkcazo | Iyunithi | ZJ-200 |
| ﹡ umgaqo wokusebenza: ukufunxa ngesifunxa﹡ ukuqalisa ngokuzenzekelayo kwaye umise isenzo sokulayisha | |||
| Umsebenzi: shaja iigranuli ze-PE kwi-hopper dryer | |||
| 1 | Uxinzelelo oluzinzileyo max. | Pa | 9800 |
| 2 | Amandla emoto | KW | 1.1 |
| 3 | Kufuneka umbane wombane | Njengesicelo | |
| 4 | umthamo | 5m | 200kg/h |
| 10m | 150kg/h | ||
| 5 | Umthamo wehopper yokufunxa | L | 10 |
2.1 iseti ye-Hopper dryer
| NO | Inkcazo | Iyunithi | Amagqabantshintshi |
| 1 | Idayamitha yomphanda | mm | 600 |
| 2 | Izinto eziphathekayo | / | Yenziwe ngentsimbi eshayinayo |
| 3 | Ifestile yeglasi yokubona | / | Ewe |
| 4 | Phantsi ipleyiti yocango lwesilayidi | / | Ewe |
| 5 | Amandla okufudumeza | Kw | 9 |
| 6 | Amandla okuvuthela umoya | kw | 0.55 |
3. Iseti e-1 ye-SJ65/33 extruder screw enye
| ﹡Isikruru, uyilo lomphanda kunye nokuveliswa kufunxa itekhnoloji ephucukileyo yaseYurophu (ukusuka kwinkampani enkulu edumileyo yomphanda)﹡Isikruphu kunye nezinto zomgqomo:38CrMoAlA, i-nitriding iphathwa ﹡Isikrufu esikhethekileyo semathiriyeli ye-PE qinisekisa isiphumo esihle seplastiki ﹡Yamkela izixhobo zombane ezidumileyo ezinomgangatho osebenzayo ozinzileyo. ﹡Ibhokisi yeGear: itorque ephezulu, ingxolo ephantsi, izinyo legiya elukhuni ubuso obunikezelweyo kwibhokisi yegiya ye-extruder ﹡Inkqubo yokuzikhusela: Ngaphezulu kokhuseleko lwangoku lwemoto Ngaphezulu koxinzelelo lokukhusela isikrufu | ||
| Inkcazo ngokubanzi | Izinto eziphambili zombane | Isiguquli samaxesha amaninzi:ABB/deltaUmnxibelelanisi we-AC: Schneider okanye siemens Ukutshintshela ikhefu lomoya: Schneider Umlawuli wobushushu: omron/delta Imitha yombane kunye nemitha yangoku: DELIXI |
| Isiphumo | Malunga nama-200kg/h | |
| Xhuma uhlobo lwe-extruder kunye nokungunda | Uqhagamshelo lwebholithi | |
| Iingenelo | Amalungu aphambili amkela uphawu olukwinqanaba eliphezuluUlawulo olungqongqo lwexesha lokwenyani | |
| Screw | Ububanzi (mm) | 65mm |
| L/D | 33/1 | |
| Izinto eziphathekayo | I-38CrMoAlA, iNitrogen inyangwe | |
| Ukufudumeza | Ukugalela isifudumezi se-aluminiyam kunye nesigqubuthelo sangaphandle sentsimbi engatyiwayo | |
| Amacandelo okufudumeza | indawo ye-5 | |
| Amandla okufudumeza | 20kw | |
| Umphanda | Uhlobo lomphanda | Ngegroove yokutya;Ukupholisa amanziinlet orifice |
| Ukupholisa | Ukupholisa ngokuvuthela,ukuchaneka kolawulo lobushushu: ±1℃ | |
| Icandelo lokupholisa | 5 amacandelo | |
| Izinto eziphathekayo | I-38CrMoAlA, iNitrogen inyangwe | |
| Qhuba kwayeInkqubo yothumelo | Amandla enjini aphambili (KW) | I-55kw uphawu oludumileyo eTshayina |
| Imowudi yokulungelelanisa isantya semoto ephambili | Uguqulo oluguquguqukayo lwamaza | |
| Isantya esijikelezayo senjini engundoqo (r/min) | 1500r/min | |
| Ibhokisi yegiya | Ubuso bezinyo elinzima Uyilo lwengxolo ephantsiShaft: NSK yaseJapan Izinto eziphathekayo: 20CrMnTi | |
4. Iseti e-1 yomgca wamanqaku co-extruder SJ25/25
| Into | Inkcazo | Iyunithi | SJ25/25 |
| 1 | Ububanzi beScrew | mm | 25 |
| 2 | Umlinganiselo wobude ukuya kwidayamitha |
| 25:1 |
| 3 | Isiphumo | Kg/h | 1.5-10 |
| 4 | Ukujikeleza kwesantya seScrew | rev/min | 5-50 |
| 5 | Izinto ze-Screw barrel kunye ne-Screws |
| 38CrMoAlA |
| 6 | Ibhokisi yegiya |
| Ubuso bezinyo elilukhuni, uyilo lwengxolo ephantsi |
| 7 | Ukufudumeza Umthamo we-Screw barrel | KW | 6 |
| 8 | Iindawo zokufudumeza zombhobho |
| 2 |
| 9 | Amandla eMoto angundoqo | Kw | 0.75 |
| 10 | IMowudi yokuLungisa isantya |
| ukuguqulwa rhoqo |
| 11 | Ukupholisa umphanda |
| Ukupholisa ukuhamba komoya, iindawo ezi-2 |
| 12 | Ubude be-Screw Axes | mm | 1000 |
| 13 | Umlawuli wobushushu |
| Igama Brand: i-omron, eJapan |
| 14 | Isiguquli samaxesha amaninzi |
| Uphawu:ABB, Japhan |
| 15 | Umzobo womzobo | mm | 1450×450×1500 |
| 16 | Ubunzima | kg | 250 |
5. Iseti ye-1 yokubumba kwimibhobho ye-HDPE enobubanzi obuvela kwi-16--110mm
| Into | Inkcazo | Iyunithi | Phawula | ||||
| ﹡ Isikali sohlobo olutsha qinisekisa ukuba unesiphumo esilungileyo sokupholisa kunye nesantya esiphezulu se-extrusion
| |||||||
| 1 | Uluhlu lwedayamitha(OD) | mm | 16-110mm | ||||
| 2 | Ubunzima bodonga | / | ngokwesicelo somthengi | ||||
| 3 | Izinto zokungunda | / | 40Cr | ||||
| 4 | Isixhobo sokulinganisa i-Bushing | / | Sternum Bronze ubhedu | ||||
| Inkcazo | Ubunzima bodonga PN10(SDR17) | Ubunzima bodonga PN16 (SDR11) | |||||
| 16mm | 1.8mm (SDR9) | ||||||
| 20mm | 1.9mm | ||||||
| 25mm | 1.8mm | 2.3mm | |||||
| 32mm | 1.9mm | 2.9mm | |||||
| 40mm | 2.4mm | 3.7mm | |||||
| 50mm | 3.0mm | 4.6mm | |||||
| 63mm | 3.8mm | 5.8mm | |||||
| 75mm | 4.5mm | 6.8mm | |||||
| 90mm | 5.4mm | 8.2mm | |||||
| 110mm | 6.0mm | 10.0mm | |||||
6. Iseti e-1 yeVacuum Ukulinganisa kunye netanki yokupholisa
| NO | Inkcazo | Iyunithi | Phawula |
| ﹡ ulawulo lwamanzi oluzenzekelayo﹡ ikhabhinethi yombane kunye nokukhusela amanzi ﹡ ukupholisa kwamanzi okugxininiswe ngamandla okutshiza ngesiphumo esihle sokupholisa ﹡ impompo yokufunxa kunye nempompo yamanzi ithatha impompo ekrelekrele enomsebenzi wokuzikhusela ﹡ Uyilo lwemibhobho olugqibeleleyo lunokugcina umlomo ungavalwanga
| |||
| Umsebenzi: linganisa iidamitha zangaphandle kunye nombhobho wokupholisa kuqala | |||
| 1 | Ubude betanki | mm | 6000 |
| 2 | Izinto zetanki yamanzi | intsimbi engatyiwa, SUS304 | |
| 3 | Ubungakanani bezinto eziphathekayo | I-Stannum-bronze | |
| 4 | Imo yokupholisa | Ukupholisa ngokutshiza | |
| 5 | Iindawo zokugalela | 4 | |
| 6 | Amandla eMpompo yamanzi | KW | 1.5kw×2 iseti |
| 7 | Vacuum Pump Amandla | KW | 4kw |
| 8 | Isidanga seVacuum | Mpa | -0.03—0.05 |
| 9 | Uluhlu olushukumayo lwePhambili nangasemva | mm | ± 600, ukuqhuba imoto |
| 10 | Up-down Uhlengahlengiso Range | mm | ±50, ngesandla |
| 11 | Umzobo womzobo | mm | 6000×650×1250 |
| 12 | ubunzima | kg | 1250 |
Iseti e-1 ye-Hailing off Machine
| NO | Inkcazo | Iyunithi | Phawula |
| ﹡I-pneumatic clamping, uhlengahlengiso lwesantya esiguqukayo ﹡ukwamkela isilinda sohlobo oludumileyo | |||
| Umsebenzi: Khupha umbhobho we-PE ngokuzinzileyo kunye ne-synchronal ngesantya se-extruder | |||
| 1 | Ubude be-pedrail obukhoyo | mm | 1400 |
| 2 | Imowudi yokuBamba | Ngomoya | |
| 3 | IMowudi yokuLungisa isantya | Uguqulo lwamaxesha amaninzi | |
| 4 | Ukuhambisa Amandla eMoto | KW | 1.5kw*2 iseti |
| 5 | Isantya sokuHamba | m/umz | 0.5～8 |
Iseti e-1 yeprinta yelaser
Iseti e-1 yesisiki sokubala semitha
| NO | Inkcazo | Iyunithi | Phawula |
| uthuli oluzenzekelayo ukusika, kunye nomsebenzi wokubala imitha ﹡I-Saw blade ithatha i-carbide blade I-Alert Alarm kunye neseti yokubala ye-dutu cutter yasimahla | |||
| Umsebenzi: ukusika umbhobho we-HDPE ngobude obusisigxina | |||
| 1 | Uhlobo lomsiki | Umsiki wokubala imitha ozenzekelayo | |
| 2 | Umbhobho wokusika ofanelekileyo ububanzi | 16-110mm | |
| 3 | Ukusika isantya | Ungqamaniso, ukusikwa okuzenzekelayo kubude obusisigxina | |
| 4 | Amandla emoto | KW | 2.2 |
| 5 | Izinto zokusika isarha | Intsimbi ye-alloy | |
| 6 | Imowudi yokuBamba | I-Pneumatically Drive | |
| 8 | Ubuninzi bokusika ubukhulu | mm | 18 |
| 9 | Isantya esifanelekileyo sokusika | m/umz | 12 |
Ifoto yeWinder :
Iiparamitha kunye netafile yoqwalaselo lwechiller
| I-PARAMETER UMZEKELO WOKUQINISEKISA | SYF-20 | |
| Umthamo wefriji | Kw 50Hz/60Hz | 59.8 |
| 71.8 | ||
| Ukunikezelwa kwamandla kunye namacandelo ombane (eSchneider, eFransi) | 380v 50HZ | |
| Isikhenkcisi (iNtaba yaseMpuma) | Igama | I-R22 |
| Imo yolawulo | Ivalve yokwandiswa kwebhalansi yangaphakathi (Hongsen) | |
| Icompressor (Panasonic) | Uhlobo | Uhlobo lwe-vortex evaliweyo (10HP * iiseti ezi-2) |
| Amandla(Kw) | 18.12 | |
|
Icondenser (Shunyike) | Uhlobo | Ukusebenza okuphezulu kobhedu olugubungele i-aluminiyam amaphiko + ingxolo ephantsi ye-rotor fan yangaphandle |
| Amandla fan kunye nobuninzi | 0.6Kw*2 iiseti(Juwei) | |
| Umthamo womoya wokupholisa(m³/h) | 13600(Umzekelo 600) | |
|
Umphunga (Shunyike) | Uhlobo | Uhlobo lwekhoyili yetanki yamanzi |
| Umthamo wamanzi amkhenkce (m³/h) | 12.94 | |
| 15.53 | ||
| Umthamo wetanki (L) | 350(Intsimbi engatyiwayo, ukugqunywa kwangaphandle) | |
|
Impompo yamanzi (Taiwan Yuanli) | Amandla(Kw) | 1.5 |
| Phakamisa (m) | 18 | |
| Isantya sokuhamba (m³) | 21.6 | |
| Ujongano lwedayamitha yombhobho | DN50 | |
| Ukhuseleko kunye nokhuseleko | Ukukhuselwa kobushushu obugqithileyo kwiCompressor, ukhuseleko olugqithileyo, ukukhuselwa koxinzelelo oluphezulu noluphantsi, ukukhuselwa kobushushu obugqithisileyo, ukulandelelana kwesigaba/ukhuseleko lwesigaba, ukukhuselwa kobushushu obugqithisileyo. | |
| Imilinganiselo yoomatshini (Isitshizi esingaphezulu) | Mde (mm) | 2100 |
| Ububanzi (mm) | 1000 | |
| Phezulu (mm) | 1600 | |
| Igalelo lamandla ewonke | KW | 20 |
| Ubunzima bomatshini | KG | 750 |
Qaphela:1.Isakhono sokukhenkceza sisekwe:kwindawo yokukhenkceza yamanzi kwindawo yokungena kunye nobushushu bamanzi aphumayo 7℃/12℃,indawo yokupholisa kunye nobushushu bomoya wokuphuma 30℃/35℃.
2.Umda womsebenzi:uluhlu lobushushu bamanzi angumkhenkce: 5℃to35℃;Indawo ekhenkcezayo yokungena kwamanzi kunye nokwahlukana kobushushu obuphumayo: 3℃to8℃,Iqondo lobushushu elikhoyo alikho ngaphezulu kwe-35℃.
Unelungelo lokutshintsha le parameters okanye imilinganiselo engentla ngaphandle kwesaziso.
Ixesha lokuposa: Sep-13-2022